Live calculator search
Calculator Results
Search the calculator library.
View All Calculators →

Slope Calculator

Calculate construction slope, grade percentage, slope angle, and elevation change from rise and horizontal run. Use the live diagram to visualize driveway grading, patio drainage and site elevations.

Construction Slope & Grade Calculator

Live geometry • Instant results

Enter Your Measurements

Positive rise = uphill; negative rise = downhill. Run is horizontal distance, not diagonal distance.

Target Grade Planner

Live Slope Results

Slope / Grade5%
Slope Angle2.8624°
Rise : Run Ratio1 : 20
Sloped Distance20.025 ft
Live rise, run and slope diagramRun 20 ftRise 1 ftSlope 5%

Geometry updates live; dimension proportions are preserved. For extremely flat/steep slopes, the triangle is fitted to the available canvas.

How to Use the Slope Calculator

Measure rise and horizontal run, select units, and read the grade, angle, ratio and sloping distance instantly. For irregular site areas, start with our Square Footage Calculator before checking elevations.

1. Measure Vertical Rise

Record the elevation difference between two points. Enter a negative value when the ground falls in your direction of travel. For stair layouts with rise/run measurements, use the Stair Calculator.

2. Measure Horizontal Run

Use the level, horizontal distance—not the sloping ground distance. Select feet, inches, meters or centimeters. Estimate finished surface area separately with the Square Footage Calculator.

3. Review Live Results

The grade percentage, slope angle and rise-to-run ratio update immediately as dimensions change. Check the diagram for direction and proportion.

Slope Formula: Rise, Run, Percentage and Degrees

Construction grading commonly expresses a vertical elevation change relative to horizontal distance.

Calculate Slope Percentage

Slope (%) = (Rise ÷ Run) × 100

Both measurements must use the same distance units. For a 1 ft rise over a 20 ft horizontal run, the grade is 5%.

Convert Slope Percentage to Degrees

Angle = arctan(Rise ÷ Run) × 180 / π

A 5% grade has an angle of about 2.8624°. A 5-degree angle is not the same as a 5% grade.

Rise-to-Run Ratio

Write a slope as 1 vertical unit for each specified number of horizontal units. A 5% grade is 1:20.

Sloped Distance

The diagonal length is the square root of rise squared plus run squared: √(rise² + run²). If you are planning lumber quantities rather than the grade itself, try the Board Foot Calculator.

Grade Direction

Positive elevation change means uphill. Negative elevation change means downhill. Zero elevation change means level.

Construction Slope Calculation Examples

Use these examples to check grade calculations and understand differences between percentage and angle.

Driveway Slope Calculator Example

A driveway rises 3 ft across a 60 ft horizontal run: (3 ÷ 60) × 100 = 5% grade, approximately 2.862°. Estimate surfacing materials using the Asphalt Calculator or Gravel Calculator.

Concrete Patio Slope Example

A hypothetical 2% grade over a 12 ft run produces a 0.24 ft (2.88 in) elevation difference. Actual drainage design depends on site conditions and local requirements. For material estimates, visit the Concrete Slab Calculator or Concrete Calculator.

Drainage Slope Calculation

A 2 in fall over a 10 ft run equals 2 ÷ 120 × 100 = 1.6667%. For a drain pipe or shower, consult the applicable project specification. For adjacent blockwork, see the Concrete Block Calculator and Mortar Calculator.

Slope Percentage, Grade Ratio and Angle Conversion

Quick reference values help interpret common grading and elevation measurements.

GradeRise : RunAngle (approx.)Elevation change over 20 ft
1%1:1000.5729°2.4 in
2%1:501.1458°4.8 in
5%1:202.8624°12 in
10%1:105.7106°24 in
20%1:511.3099°48 in

Where a Construction Grade Calculator Helps

Explore slope measurement methods for common projects while checking project-specific safety and drainage requirements.

Driveway and Site Grading

Measure a change in ground elevation over the horizontal distance. The driveway slope calculator approach makes grade percentages comparable across a site, regardless of measurement units. Planning a paved surface? Compare material needs with the Paver Calculator, Gravel Calculator and Asphalt Calculator.

Patio and Concrete Slab Drainage

Convert desired drainage grade into a measurable rise or fall. For a concrete patio or slab, also consider finished surface elevations, water flow paths and local requirements. Then calculate quantities with the Concrete Slab Calculator, Rebar Calculator and Concrete Footing Calculator where applicable.

Drainage Pipes and Trench Planning

A drainage slope calculator expresses planned pipe fall relative to horizontal run. Pipe-sizing and minimum slope must be evaluated from the relevant plumbing code and engineering criteria.

Ramp and Accessibility Planning

Use the percent slope calculator to describe existing or proposed grades. The tool does not verify ADA compliance, landings, cross slopes, handrails or other accessibility requirements. For nearby step geometry, use the Stair Calculator separately.

From Site Grade to Construction Material Planning

A grade calculation identifies elevation change. The right material estimator depends on what you plan to build on that surface.

Groundwork and Exterior Surfaces

For paths and hardscape projects, estimate surface materials with the Paver Calculator, Brick Calculator and Mortar Calculator. A Fence Calculator can help plan boundary runs across graded ground, while a Deck Calculator helps estimate deck materials. Landscaped areas may also call for a Mulch Calculator.

Concrete and Masonry Projects

After checking site levels, use the Concrete Calculator, Concrete Footing Calculator or Concrete Block Calculator for distinct material estimates. These tools do not replace grading or structural design.

Framing and Exterior Finishes

For construction above the graded area, use the Stud Calculator, Plywood Calculator and Board Foot Calculator for their different framing and sheet-material tasks. The Siding Calculator and Roofing Calculator cover separate exterior systems.

Interior Finishes and Cost Estimates

Where a project includes indoor work, estimate materials using the Drywall Calculator, Insulation Calculator, Paint Calculator, Wallpaper Calculator, Tile Calculator or Flooring Calculator. Collect component estimates with the Building Material Cost Calculator.

For volumes rather than grade, the Cubic Yard Calculator handles general volume conversions. Choose the material-specific estimator when density, coverage, waste or packaging matters.

Frequently Asked Questions

Answers to common questions about rise and run, grade percentages and construction slopes.

How do I calculate slope percentage?

Divide vertical rise by horizontal run in matching units, then multiply by 100. A rise of 1 ft over 20 ft is a 5% grade.

Is a 5% slope equal to a 5-degree angle?

No. A 5% slope corresponds to approximately 2.8624°, while 5° corresponds to approximately 8.75% grade.

How do I calculate horizontal run from a required grade?

Divide the rise magnitude by the desired grade written as a decimal. A 1 ft rise at 2% grade requires a 50 ft horizontal run.

Can I measure uphill and downhill grades?

Yes. Enter positive rise for uphill and negative rise for downhill. The magnitude describes steepness; the sign identifies direction.

Does the diagram change with rise and run?

Yes. The diagram recalculates on every valid edit and preserves the triangle’s rise/run proportions. Extremely steep or shallow slopes are fitted to the SVG view box without hiding measurements.

Can this tool confirm ADA ramp slope requirements?

No. It calculates geometric grade only. Accessibility design requires additional specifications and checks not covered by this calculator.

What is the difference between horizontal run and sloped distance?

Horizontal run is level distance between the points. Sloped distance follows the incline and is longer when the rise is not zero.

Is a 2% slope always right for concrete drainage?

No universal slope fits every surface or project. A 2% grade is a calculation example, not a substitute for site-specific design or relevant standards.